Advertisement
avatar: jjj
jjj
7 posts
Replied to jjj's post on June 16th, 2015

I downloaded the service manual for the 5804/5810 centrifuge from this site. Unfortuantely the quality is not so good so I cannot read most of the text on the diagrams (section 8). Also the pictures that are in this manual look rather different from my machine. Mine is a 5810R and I realize that some pictures are of the R model and some are not, but even the ones of the R model don't look like mine. In particular is the breaking resistor.

If you're wondering, I am having an error 6 problem. Can anyone help me out with some better documentation?

avatar: jjj
jjj
7 posts
Replied to jjj's post on June 16th, 2015

Good news and bad news.

The good news is that I found good quality schmatics for the 5810/5804. I will upload them to this site if someone tells me how to do it. Perhaps the admin can add them to the file they already have.

The bad news is that there are newer and older versions of these machines. "Refresher" is the newer version and "Non-Refresher' is the older version. I have the older version and Eppendorf no longer has a service manual for the non-refresher.

A bit of good news, I found a schematic for the older non-refresher version. I will also upload this one as soon as I find out how to do that.

So, does anyone have a Non-refresher Service Manual?

avatar: medphysteo
medphysteo
287 posts
Replied to jjj's post on June 17th, 2015

What's your email address?

avatar: jjj
jjj
7 posts
Replied to medphysteo's post on June 17th, 2015

jamesderrick@yahoo.com

 

I have since traced the problem to the frequency converter card. Now the problem is that I can't take this card apart. It has a metal base on it that I need to take off to access the bottom of the circuit card. Anyone know how to do this?

avatar: medphysteo
medphysteo
287 posts
Replied to jjj's post on June 17th, 2015

James,

I just noticed the pre-2006 58xx schematics show the motor driver is an ST Micro L298N 15-pin dual full bridge IC.

avatar: Cummins
Cummins
3 posts
Replied to jjj's post on January 30th, 2017

Hi jjj & medohysteo,
I was wondering if you ened up uploading the detailed schematics? I'm doing a board repair and they would be of great help.

Many thanks,

Dan.

daniel.cummins@anu.edu.au

 

Quote jjj

Good news and bad news.

The good news is that I found good quality schmatics for the 5810/5804. I will upload them to this site if someone tells me how to do it. Perhaps the admin can add them to the file they already have.

The bad news is that there are newer and older versions of these machines. "Refresher" is the newer version and "Non-Refresher' is the older version. I have the older version and Eppendorf no longer has a service manual for the non-refresher.

A bit of good news, I found a schematic for the older non-refresher version. I will also upload this one as soon as I find out how to do that.

So, does anyone have a Non-refresher Service Manual?

 

 

avatar: Cummins
Cummins
3 posts
Posted January 30th, 2017

Thanks medphysteo,

I was hoping there would be a manual with some actual PCB circuit diagrams so I could do a board level repair on the power supply...but it doesn't look like they are available sadly.

avatar: medphysteo
medphysteo
287 posts
Replied to Cummins post on January 30th, 2017

No, Eppendorf never published that level of detail, even for their tech staff. You might get some steers from some of the other Eppendorf model forums on this site or medwrench, though. Some of the guys have hacked in pretty well and come up with good fixes.

avatar: sfantos
sfantos
2 posts
Replied to medphysteo's post on May 13th, 2018
Hi jjj & medohysteo, I was wondering if you are using the detailed schema? I'm doing a board repair and they would be of great help.   Thank you so much,

Sidnei

sidneisantos_22@hotmail.com

avatar: sfantos
sfantos
2 posts
Replied to jjj's post on May 13th, 2018
Hi friend you have the 5810r manual could you send me   thank you.   Sydney   sidneisantos_22@hotmail.com
avatar: Grant Wise
Grant Wise
3 posts
Replied to jjj's post on June 7th, 2018

Still have 5810 R Service Manual?

 

avatar: Reigo
Reigo
1 posts
Replied to Grant Wise's post on September 6th, 2018

Would some one share the schematics for eppendorf 5810 with me also

 

My email is reigo.tamm@regionaalhaigla.ee

avatar: BGantt
BGantt
10 posts
Replied to sfantos post on September 24th, 2018

If anyone has a copy of the 5810R service manual. Please send me a copy: brugantt@hotmail.com

avatar: JPereira
JPereira
1 posts
Replied to jjj's post on November 15th, 2018

Hi, good morning,

I need to see some references of:

- Cover shock absorber;

- Annual KIT maintenance (rubber copper motor, cinoblocks, etc ...);

- Support for tubes (attached image);

 

Can u send me the service manual please? My email: joaopereira04@gmail.com

Thank u.

avatar: Scientific
Scientific
2 posts
Replied to Cummins post on November 26th, 2018

Can you send schematic diagram to scientific@outlook.co.nz for 5810R?

avatar: kirodji
kirodji
1 posts
Replied to jjj's post on December 1st, 2018

Hi

How are you?

I need the service manual

I have 5810 centrifuge

kirodji@hotmail.com

Best Regards,

Roger

avatar: friservice
friservice
1 posts
Replied to kirodji's post on January 22nd, 2019

Hi

How are you?

I need the service manual of 5810R centrifuge

service@frilabo.com

Can you send me please?

Have a nice day

 

avatar: rboice
rboice
1 posts
Replied to friservice's post on February 14th, 2019

Hello  All

I need schematics for a older 5810R. I'm getting a "NO ROTOR" error after pressing start. I'm interested in doing componenet level repair. Any reply would be appreciated. Russel.Boice@gmail.com now at wayne state university.

 

avatar: dgsr2
dgsr2
1 posts
Replied to jjj's post on February 22nd, 2019

Hi Freind,

     Could you send me a copy of the service manual i'm working on a 5810 that needs the speed adjusted. can you help me out?

send to Desmond.Gayle@va.gov

Best Regards,

dgsr2 

avatar: Kevin_K
Kevin_K
1 posts
Replied to dgsr2's post on March 5th, 2019

Hi there, 

 

Can you also send me the service manual for the 5810R centrifuge?

 keivn.khan27@gmail.com

 

 

Replied to jjj's post on April 9th, 2019

Hello  I need service manual or diagram for centrifuge 5810R 

send atachment  vmcc.amplibio@gmail.com

regards

avatar: IPetev
IPetev
1 posts
Replied to medphysteo's post on May 3rd, 2019

Hi

I need  service manual for 5810 centrifug.

ipetev@medicoservice.net

Best Regards,

Ivan Petev

avatar: rdttech
rdttech
2 posts
Replied to IPetev's post on June 28th, 2019

Hello,

Please, in need of the service manual, grants are coming and need the documentation, please please.

ron.thorpe@acuramed.com

avatar: rdttech
rdttech
2 posts
Replied to rdttech's post on July 1st, 2019

Please please still in very much need of service manual.

HELP

ron.thorpe@acuramed.com

avatar: Tommy CB
Tommy CB
2 posts
Replied to jjj's post on July 28th, 2019
Will you be so Kind and send a copy of the service diagram to tcbermej@gmail.com thank you
avatar: StenoBio
StenoBio
4 posts
Replied to Tommy CB's post on October 29th, 2019

is the only way to get this service manual to post your email and wait?  isn't there a better way to do this?

isaac.mehl@gmail.com

avatar: alejandropa
alejandropa
3 posts
Replied to jjj's post on November 6th, 2019

Dear Sr.

 

Please send me the service manual and the schematic.

alejandro.palomino.amaro@gmail.com

 

Thank you!