Advertisement
avatar: ilyas
ilyas
6 posts
Replied to ilyas post on March 4th, 2018

HELLO

I HAVE A BRUKER D8 ADVANCE IN MY LAB.I HAVE REPAIRED THE EXTERNAL COOLING SYSTEM ,AND WHEN I TRIED TO LAUNCH THE MACHINE AN ERRER HAS BEEN OCCURED: XRD COMMANDER HANGED OUT. SO WHAT SHALL I DO?

avatar: TEKLINK
TEKLINK
7 posts
Replied to ilyas post on March 4th, 2018

Hi, What type of D8 Advance do you have? Is it a DaVinci system? If you do not know, how old is the instrument? Did you try to reboot the PC and restart the instrument, also try to download the configuration program? Then turn on the generator first, then try to connect with commander. Do you have a program called D8 tools on your PC?

Kind regards,

Dave

avatar: ilyas
ilyas
6 posts
Replied to TEKLINK's post on March 6th, 2018

Hello

I have a Bruker D8 series 2 diffractometer with lynx eye system,it has been delivered in 2008, and yes i have D8 tools. 

I did all this steps but nothing seems to work.But yesterday i discovered that may cooling system is broken the gas is mixed with the cooling liquide.

your faithfully,

Ilyas  

avatar: TEKLINK
TEKLINK
7 posts
Replied to ilyas post on March 6th, 2018

Hi Ilyas,

Do you have flow at the site glass on the front of the chiller. I assume you have a Haskris R100. The flow at the chiller should be about 1.0-1.5/gall. Per/min With the D8 turned on.

Can you then connect with D8 tools and look at the generator and see what the flow rate is. It should be above 3.6 l/per min. You would also need to reset both software and hardware capture registers, then send the x-ray on command. At that point turn on the generator if the flow rate is above 4.0 l/per. Min. In D8 tools.

I have seen some coolant leak into the resovoir, it should still work. You should drain the tank and re-fill with distilled water and check to make sure the chiller cycles correctly.

Can you do a file and save as and send it to teklink@icloud.com?

Kind regards,

Dave

avatar: ilyas
ilyas
6 posts
Replied to TEKLINK's post on March 8th, 2018

Hi Dave I will try this as soon as possible thanks.

avatar: TEKLINK
TEKLINK
7 posts
Replied to ilyas post on March 21st, 2018

Hello Ilyas,

How did you make out with the problem with the D8?

Kind regasrds,

Dave

 

avatar: ilyas
ilyas
6 posts
Replied to TEKLINK's post on March 28th, 2018

Hello Dave

I haven't done anything yet ,because i found that the cooler is down so I sent it to repair. When I recover it I will let you know.

Thanks Dave.

                               your faithfully,

Ilyas 

 

avatar: Steve01
Steve01
6 posts
Replied to TEKLINK's post on July 14th, 2019

Hi Dave,

 

I have a 2 years old Bruker XRD and it showed generator error 21 (max KV overshoot). Is there a hardware reset we can do. I did safety board reset but  that didnt help. Whatelse we can do to fix this issue.

 

Thanks

 

Steve

avatar: Steve01
Steve01
6 posts
Replied to TEKLINK's post on July 14th, 2019

Hi Dave,

 

I have a 2 years old Bruker XRD and it showed generator error 21 (max KV overshoot). Is there a hardware reset we can do. I did safety board reset but  that didnt help. Whatelse we can do to fix this issue.

 

Thanks

 

Steve

avatar: TEKLINK
TEKLINK
7 posts
Replied to Steve01's post on July 14th, 2019

Hi Steve,

In the older generators error 21 was power cut. There is no error 21 in the Davinci, interesting. So what I would do is close the measurement software, stop and exit the measerver bottom right by the clock. Power off the D8 from the withe then red switch on the lower left side and wait 30 seconds. Turn on the D8 power again and let it boot. When it is done booting start the measurement software and then go to the tools tab. Then try to turn on the generator.

Do you get any errors now? Are there any error icons flashing on the generator button?

If no x-rays can you send a status file from tools.

Thanks,

Dave

avatar: Steve01
Steve01
6 posts
Replied to TEKLINK's post on July 15th, 2019

Hi can you send me your email address, I will send you the state file.

Thanks

avatar: TEKLINK
TEKLINK
7 posts
Replied to Steve01's post on July 15th, 2019

teklink@icloud.com

avatar: Steve01
Steve01
6 posts
Replied to TEKLINK's post on July 15th, 2019

sent you details to your email

avatar: AJAlexxx
AJAlexxx
13 posts
Replied to ilyas post on July 18th, 2019

Hi, does your Bruker D8 OK now?

zetans

avatar: billym2418
billym2418
1 posts
Replied to AJAlexxx's post on August 1st, 2019

I hope your Bruker D8 is running smoothly now. And it can now do very diverse analytical needs with highest competence.

online-application.org/social-security-administration-office/oklahoma/

Replied to ilyas post on August 7th, 2019

Cool. can I share this post to my blog? I'd appreciate it. Cheers! summoners war quiz event answers

avatar: Everhart
Everhart
8 posts
Replied to ilyas post on August 8th, 2019

Some of advice are actually sounds great.  our site

avatar: ManuelR
ManuelR
2 posts
Replied to Everhart's post on August 14th, 2019

I just followed your instruction, Dave and it went okay in my end. Thanks!

www.concretecontractorsfayettevillear.com

avatar: Joshua A. Price
Joshua A. Price
33 posts
Replied to ilyas post on August 14th, 2019

I've spent ages looking for this on the web. Thank God someone did post it. Thanks. our site

avatar: TEKLINK
TEKLINK
7 posts
Replied to Joshua A. Price's post on August 14th, 2019

Joshua,

What post are you talking about? And what have you been searching for?

Regards,

avatar: Danielperez123
Danielperez123
2 posts
Replied to TEKLINK's post on August 15th, 2019

Thanks for your procedure, big help for me! | here

avatar: TEKLINK
TEKLINK
7 posts
Replied to Danielperez123's post on August 15th, 2019

www.teklink-us.com

avatar: CliffA
CliffA
1 posts
Replied to ManuelR's post on August 17th, 2019

Perfect! Thanks for the update and helpful info. I too was able to proceed with success. Cliff - Tile Winnipeg | christmaslightinstallationwinnipeg.ca/contact-us

avatar: RheyGo
RheyGo
1 posts
Replied to ilyas post on August 21st, 2019

Nice thread! I was following this thread as I have same problem with yours. Did you have your problem solved now? mold remediation

avatar: Mike888
Mike888
1 posts
Replied to TEKLINK's post on August 21st, 2019

Hi Dave,

I'm compiling this problems here with your solution for my daughter's Lab reference. Thanks for posting!

Mike - accident towing | roadside assistance car repair services

avatar: Horea
Horea
1 posts
Replied to ilyas post on August 21st, 2019

Relieved to know that the solution to my problem is here! Thank goodness! :)

Gucci Bag