1. Home
    2.  / 
  2. Basic Laboratory
    3.  / 
  3. Glassware Washers
    4.  / 
  4. Standard Capacity Washers
    5.  / 
  5. Miele - G 7826/G 7825

Miele - G 7826/G 7825

Manufactured by  Miele
Follow this Equipment

High performance machines with a width of only 900 mm. The optimum solution for central and decentralized instrument preparation in hospitals.

The Miele G 7826 Lab Glassware Washer System is designed to provide high-throughput glassware cleaning in areas where space is at a premium. This unit is ideal for cleaning both large and small volume of items. This high tech system has been proven in hundreds of laboratories worldwide. It features the user-friendly Profitronic programming system for easy programming, a fully modular basket system for wash load flexibility, and an automatic basket recognition system to help eliminate user error. Because of its remarkably low noise and heat emissions, this unit is also ideal for in-lab use.
Active Questions & AnswersAsk a Question

There are no current Discussions

Standard Capacity Washers Service ProvidersView All (7)

Request Support
Features of G 7826/G 7825
          
  • 3-fold filter system with wash cabinet filter, coarse filter and micro-fine filter   
  • Flow meter counter for control of water intake   
  • Boiler for heating demin. water   
  • Boiler capacity: 21 l   
  • Electrical door lock   
  • Peak-load cut-out   
  • Sensors for automatic mobile unit recognition   
  • Programme failure check   
  • 2 spare sensors for temperature monitoring and control   
  • Comprehensive safety features in accordance with EN ISO 15883   
  • Sensor port   
  • Emergency release on unclean side 
General Specifications
Depth 29.3 in
Flow Rate700 L/min
Height77.8 in
Internal Depth 24.3 in
Internal Height 26.9 in
Width 35.3 in
Internal Width 21.3 in
Maximum Temperature95 °C
Power Requirements 208 V, 60 Hz,
Noise Level70 dB
Recirculation Pump (flow rate)6.9 gal/min 5.3 gal/min (20 l/min) for chamber fill 1.6 gal/min (6 l/min) for steam condenser fill
Drying SystemForced Air
Washer CapacityStandard Capacity
Washer OrientationFreestanding
Additional Specifications

Profitronic: Profitronic control system with programmable wash options, available automatic basket recognition (AWK),      
RS 232 for connection to printer or PC, and multiple selectable languages on an easy-to-read LCD screen      
Standard: 11 standard wash programs with utility programs      
Custom: 45 available spaces for custom wash programs to be created and stored      
      
Temperatures      
Wash: Freely adjustable up to 95° C      
Final Rinse: Freely adjustable up to 95° C      
      
Cleaning Mechanism      
Rotary: Dual spray arms located at the top and bottom of chamber, third spray arm on upper basket      
Direct Injection: Upper, lower, and dual injection baskets available      
      
Drying Optional; HEPA-filtered forced-air drying system w/ freely adjustable time and temp. settings w/ cool-down step      
Temp adj.: 140-239° F (60-115° C), 1° C increments; time adj.: 1-240 min., 1 minute increments      
Water Softener Optional; Built-in softener with easily programmed water hardness control      
Steam Condenser Optional; no external venting required      
      
Neutralizer Dispensing      
Neutralizer: 1 peristaltic dosing connection for 10L container, stored on-board      
2 additional peristaltic dosing connections for 10L containers optional      
      
Cabinet and Chamber Construction      
Exterior: Brush finish type 304 stainless steel top, front, sides and bottom      
Interior: Type 316 stainless steel chamber sides, back and top      
Type 316 stainless steel chamber floor and door      
      
Plumbing Connections      
Tap (2 connections):       
a) Hot water for wash cycles: One 1/2” ID pressure hose, 5’ 7” long with 3/4” hose thread      
Input pressure: 30 - 147 PSI, min. flow rate of 3.9 gal/min (15 l/min)      
Max incoming water temperature: 158° F (70° C)      
b) Cold water for wash cycles: One 1/2” ID pressure hose, 5’ 7” long w/ 3/4” hose thread      
Input pressure: 30 - 147 PSI, min. flow rate of 3.9 gal/min (15 l/min)      
Max incoming water temperature: 158° F (70° C)      
DI (2 connection):       
c,d) DI water for rinse cycles: Two 1/2” ID pressure hoses, 5’ 7” long with 3/4” hose thread      
Input pressure: 30 - 147 PSI, min. flow rate of 3.9 gal/min (15 l/min)      
Max incoming water temperature: 158° F (70° C)      
      
Drain Connections      
Connection: Two 1” OD, one 3/8” OD flexible drain hoses, 4’ 11” long; max drain height = 3’. Max drain length = 13’      
If steam condenser installed, optional 1/2” ID drain line provided; 3” min. floor drain or standpipe required      
Flow Rate: Maximum amount of water a drain needs to accept would be both numbers at the same time: 6.9 gal/min      
5.3 gal/min (20 l/min) for chamber fill      
1.6 gal/min (6 l/min) for steam condenser fill      
Steam Drying Option: A more efficient solution than heating with electric alone      
36 - 145 PSI required; two 1/2” threaded connections provided for steam connection and condensate/return      
Requires compressed air option (see below)      
Compressed Air (req w/ Steam): 85 - 175 PSI required

Looking for New or Used Equipment?

Shop on LabX

Shop on Labx.com