Miele - G 7836
Superior Cleaning, HEPA-Filtered Drying Lab Glassware Washer
In addition, the unit features HEPA filtered forced-air drying designed to dry glassware completely inside and out, and automatic liquid detergent and neutralizer dispensing with on-board storage.
Active Questions & AnswersAsk a Question
Recent Questions & Answers
Updated byApplications
Standard Capacity Washers Service ProvidersView All (7)
Documents & ManualsView All Documents
Features of G 7836
HEPA-filtered forced-air drying Profitronic controller
- 12 standard wash programs
- 44 additional custom program spaces
- Freely programmable Standard liquid dispensing
- Bellows-type detergent pumps
- 1 on-board 5L liquid detergent dispenser
- 1 on-board 5L liquid neutralizer dispenser
- Two optional off-board 5L dispensers Adjustable main wash and DI rinse
- Adjustable from ambient to 95° C 158 gpm high-flow circulation
- Separate drain & circulation pumps Standard RS-232 port Optional automatic basket recognition Standard stainless steel exterior
General Specifications
| Depth | 27.6 in |
| Flow Rate | 600 L/min |
| Height | 46.3 in |
| Internal Depth | 19.7 in |
| Internal Height | 19.7 in |
| Width | 35.5 in |
| Internal Width | 21.1 in |
| Maximum Temperature | 95 °C |
| Power Requirements | 3 AC 208 V, 60 Hz, 3 x 20 Amps, 6.6kW total load. (Unit is equipped with a 5’11”, 12/4 AWG unterminated power cord) |
| Noise Level | 70 dB |
| Recirculation Pump (flow rate) | Maximum amount of water a drain needs to accept would be both numbers at the same time: 3.5 gal/min 2.5 gal/min (10.5 l/min) for chamber fill 1 gal/min (4 l/min) for steam condenser fill |
Additional Specifications
Control Unit
Profitronic: Profitronic control system with programmable wash options, available automatic basket recognition (AWK),
RS 232 for connection to printer or PC and 13 languages on an easy-to-read LCD screen
Standard: 12 standard wash programs with utility programs
Custom: 44 available spaces for custom wash programs to be created and stored
Temperatures
Wash: Freely adjustable up to 95° C
Final Rinse: Freely adjustable up to 95° C
Cleaning Mechanism
Rotary: Dual spray arms located at the top and bottom of chamber, third spray arm on upper basket
Direct Injection: Upper, lower, and dual injection baskets available
Drying: HEPA-filtered forced-air drying system w/ freely adjustable time and temperature settings w/ cool-down step
Temp adj.: 140-239° F (60-115° C), 1° C increments; time adj.: 1-240 min., 1 minute increments
Water Softener: Built-in softener with easily programmed water hardness control
Steam Condenser: Included; no external venting required
Neutralizer Dispensing
Neutralizer: 1 Bellows-type liquid dispenser standard; neutralizer dispensed directly from 5L container in pull-out drawer
Optional: 2 additional bellows-type dosing connections for 5L containers optional, also stored in pull-out drawer
Main Circulation Pump
Circulation: 158 gal/min (600 l/min)
Pump includes sensor to protect against overheating
Cabinet and Chamber Construction
Exterior: Brush finish type 304 stainless steel top, front, sides and bottom
Interior: Type 304 stainless steel chamber sides, back and top
Type 316 stainless steel chamber floor and door
Plumbing Connections
Tap (3 connections):
a) Hot water for wash cycles: One 1/2” ID pressure hose, 5’ 7” long with 3/4” hose thread
Input pressure: 10 - 147 PSI (recommended 25 - 60 PSI), minm flow rate of 2.5 gal/min (10.5 l/min)
Max incoming water temperature: 158° F (70° C)
b, c) Cold water for wash cycles & steam condenser: Two 1/2” ID pressure hoses, 5’ 7” long w/ 3/4” hose thread
Input pressure: 10 - 147 PSI (recommended 25 - 60 PSI), minm flow rate of 2.5 gal/min (10.5 l/min)
Max incoming water temperature: 158° F (70° C)
DI (1 connection): d) DI water for rinse cycles: One 1/2” ID pressure hose, 5’ 7” long with 3/4” hose thread
Input pressure: 25 - 145 PSI; if DI system is less than 25 PSI, a pump kit is recommended
Max incoming water temperature: 158° F (70° C)
Drain Connections
Connection: Two 7/8” ID flexible drain hoses, 4’ 11” long; max drain height = 3’. Max drain length = 13’
Recommended connection to separate standpipe