Beckman Coulter - Optima L-80 XP Ultracentrifuge
No Documents
The Beckman Optima™ L-80 XP Ultracentrifuge is designed to speed up the discovery process in research involving proteomics, cytomics, or genomics.
Featuring a superior on-board computer, high-performance Optima eXPert software, and an easy-to-use touch screen, the L-80 XP offers state-of-the-art functionality, heightened user efficiency, and the fastest turnaround rates. This Beckman centrifuges enhances centrifugation knowledge by assisting the user in selecting the rotor and labware for a specific application, and in developing the most efficient centrifugation methods.
The Beckman L-80 XP uses the most sophisticated technology and materials to perform at a speed of up to 100,000 rpm. It employs an air-cooled system to ensure energy efficiency, and an imbalance-tolerant Optima L-XP drive for safe accommodation and handling of tubes that are filled at 10% under or over.
Other useful features of the Beckman Optima™ L-80 XP centrifuge include a konical™ seal for the high pellet concentration, OptiSeal™ for easy sealing, g-Max™ for the greatest volume efficiency, and Quick-Seal® for biocontainment.
Active Questions & AnswersAsk a Question
Recent Questions & Answers
Asked bymahshad.maghoumi4767
Centrifuge Service ProvidersView All (22)
Documents & Manuals
There are no Documents or Manuals available.
Features of Optima L-80 XP Ultracentrifuge
- Superior on-board computer and easy-to-use touch screen
- Optima eXPert software
- Speeds of up to 100,000 rpm
- Air-cooled design
- Imbalance-tolerant Optima L-XP drive
General Specifications
| Depth | 37 in |
| Height | 49.5 in |
| Width | 26.5 in |
| Power Requirements | 200 |
| Orientation | Floor Standing |
| Noise Level | 53 dB (3 ft) in Front of Centrifuge < 53 dBa |
| Weight | 1025 lbs |
| Speed Range | 1000 to 80000 rpm |
| Centrifuge Type | Ultraspeed |
| Maximum RCF | 602000 xg |
| Maximum Speed | 80000 rpm |
| Refrigerated | Yes_ |
Additional Specifications
Maximum Heat Dissipation into Room under Steady-State Conditions:
3,400 BTU/hr (1.0 kW)
Set Temperature:
0 to 40°C in 1°C increments
Set Time:
To 999 hours 59 minutes; Hold for continuous runs
Speed Control:
Actual rotor speed, ± 10 rpm of set speed after equilibration (above 1,000 rpm)
Temperature Control:
± 0.3°C of set temperature (after equilibration
Ambient Temperature Range:
10 to 40°C
Humidity Restrictions:
< 95% (noncondensing)
Pollution Degree:
2
Vacuum:
Below 5 microns (0.7 Pa)
Acceleration:
10 acceleration profiles--9 slow rates or maximum acceleration from 0 to set speed
Deceleration:
11 deceleration profiles--9 slow rates, coasting to a stop without brake,
Installation Category:
Category II
Speed Display:
Actual rotor speed in 10-rpm increments below 1,000 rpm and 100-rpm increments =1,000 rpm
Ventilation Clearances Required:
5.1 cm (2.0 in) sides; 15.2 cm (6.0 in) rear
Display:
Shows the accumulated 2t to two significant digits (in exponential notation)
Material:
General purpose paint
Top Surface
Urethane paint
Keypad Material
Coated polycarbonate
Manual Operation:
Indicates time remaining in timed runs,time elapsed in Hold runs, or estimated time remaining in w2t runs
Set w²t:
Up to 9.99 × 10^14 radians squared per second
Temperature Display:
Actual rotor temperature in 0.1°C increments
Programmed Operation:
Time remaining in step