1. Home
    2.  / 
  2. Basic Laboratory
    3.  / 
  3. Evaporators/Concentrators
    4.  / 
  4. External Concentrators
    5.  / 
  5. Labconco - CentriVap Cold Trap

Labconco - CentriVap Cold Trap

Manufactured by  Labconco
Follow this Equipment

CentriVap Cold Traps collect evaporated liquid from the CentriVap Vacuum Concentrator, protecting the vacuum pump from corrosion

The CentriVap Cold Trap collects evaporated liquid from a CentriVap Concentrator, protecting an accessory vacuum pump from very low freezing point liquids. Exclusive features include: brushed, stainless steel and glacier white, epoxy-coated steel exterior with blue accents; and temperature graph that illuminates green when collector coil reaches operating temperature. Other features include: HCFC-free refrigeration system with two 1/3 hp compressors lowers cold trap to lowest temperature (depending on model) in less than 30/40 minutes; four-liter, stainless steel collector; acrylic lid with two Quick-Disconnect fittings for connection to a CentriVap Concentrator; stainless steel drain port with corrosion-resistant, nylon valve; grounding clip; and ON/OFF power switch.
Active Questions & AnswersAsk a Question

Recent Questions & Answers

avatar placemark

Asked byWrenchAdmin2

NEW CentriVap® Cold Trap collector lowers to -105°C for very low freezing point liquids
View All Questions & Answers (1)

External Concentrators Service ProvidersView All (9)

Request Support
Features of CentriVap Cold Trap
  • HCFC-free refrigeration system: Has a high capacity 1/3 hp compressor to lower cold trap temperature to -50° C (-58º F) in less than 30 minutes and accelerate start up procedures. The Ultra-Low Cold Traps have two compressors to lower cold trap temperature to -85° C (-121° F) in less than 40 minutes. The -105 Cold Traps have two compressors to lower cold trap temperature to -105 (-157° F) in less than 40 minutes.
  • Reliability guarantee: Full one year warranty is provided against defects in materials and workmanship.
  • Acrylic lid: Has two Quick-Disconnect fittings for 1/2" ID hose for connecting the Cold Trap and Concentrator.
  • Four liter stainless steel collector: Holds up to four liters of liquid and accommodates an optional Glass Insert 7397605 for use with corrosives.
  • Temperature graph: Displays relative collector coil temperature. Green LED lights indicate conditions are right for beginning a process.
  • Sleek styling: Brushed stainless steel front panel and blue accents enhance appearance.
  • International electrical configuration available: The 230 volt, 50 Hz models conform to the CE (European Community) requirements for electrical safety and electromagnetic compatibility. Other voltages available.
  • Collector drain: Corrosion-resistant nylon valve and stainless steel plumbing speed clean up and eliminate need for glass insert with non-corrosives.
  • Optional Secondary Chemical Traps: Trap Inserts for removing acids, moisture, radiochemicals and solvents minimize release of contaminants into the atmosphere.
General Specifications

There are no General Specifications available.

Additional Specifications

Refrigeration: HCFC/CFC-free refrigeration system with two 1/3 hp compressors
Time to reach low temperature: -105° C (-157° F) in less than 40 minutes
Construction: Brushed stainless steel and glacier white, epoxy-coated steel
exterior with blue accents. Stainless steel drain port with nylon valve. Grounding clip.
Collector: 4-liter stainless steel
Lid: Acrylic lid with two Quick-Disconnect fittings for 1/2

Series Modals

Labconco - -105°C Cold Trap

[+] View Model Specifications

Labconco - Cold Trap

[+] View Model Specifications

Labconco - Ultra-Low Cold Trap

[+] View Model Specifications
NewsView All Articles
NEW CentriVap® Cold Trap from Labconco collector lowers to -105°C for...
Read More

Looking for

Labconco - CentriVap Cold Trap?

Shop on LabX.com